Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
avr_bootloader:paper-avrisp_mk2 [2017/01/06 22:57] admin |
avr_bootloader:paper-avrisp_mk2 [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
===== Paper-AVRISP mkII ==== | ===== Paper-AVRISP mkII ==== | ||
- | Am AVRISP mkII clone made with Paper-PCBs. The controller is the ProMicro with the Atmel32U4 chip. The design is based on the | + | |
+ | An AVRISP mkII clone made out of Paper-PCBs.\\ | ||
+ | {{:avr_bootloader:paper-avrisp_mkii.jpg|}}\\ | ||
+ | The controller is a cheap ProMicro with the Atmel32U4 chip. The design is based on the | ||
[[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en/| | [[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en/| | ||
- | Kosakalab - Make the AVRISP mkII Clone from Arduino Leonardo / Micro]].\\ | + | Make the AVRISP mkII Clone from Arduino Leonardo / Micro]] by Kimio Kosaka.\\ |
+ | |||
+ | Front:\\ | ||
+ | {{:avr_bootloader:paper-avrisp_mkii_front.jpg?400|}}\\ | ||
+ | Back:\\ | ||
+ | {{:avr_bootloader:paper-avrisp_mkii_back.jpg?400|}}\\ | ||
---- | ---- | ||
Line 18: | Line 26: | ||
**Pin Out:**\\ | **Pin Out:**\\ | ||
{{:avr_bootloader:promicro_pinout.jpg?400|}}\\ | {{:avr_bootloader:promicro_pinout.jpg?400|}}\\ | ||
+ | |||
+ | ---- | ||
+ | ==== Paper-PCB ==== | ||
+ | {{:avr_bootloader:paper-avrisp_mkii_02.jpg?400|}}\\ | ||
+ | {{ :avr_bootloader:paper-avrisp_mkii_02.zip |}}\\ | ||
+ | |||
+ | ---- | ||
+ | ==== Software ==== | ||
+ | Connect an AVR programmer to the Pro Micro: +5V, GND, Reset, MISO, MOSI, SCLK.\\ | ||
+ | ! It should be the Reset pin on the Pro Micro board not the one of the connector !\\ | ||
+ | |||
+ | With the Avrdude erase the Arduino Pro Micro:\\ | ||
+ | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -e | ||
+ | |||
+ | Set the fuses like that: lowFuse 0xFF, highFuse 0xD9, extendedFuse 0xC3:\\ | ||
+ | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U lfuse:w:0xFF:m | ||
+ | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U hfuse:w:0xD9:m | ||
+ | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U efuse:w:0xC3:m | ||
+ | |||
+ | Burn the ATMega32U4-usbdevice_dfu-1_0_0.hex file on the Pro Micro. The file is included in the megaUSB_DFU_Bootloaders_2 folder:\\ | ||
+ | [[http://make.kosakalab.com/archives/megaUSB_DFU_Bootloaders_2.zip]]\\ | ||
+ | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U flash:w:ATMega32U4-usbdevice_dfu-1_0_0.hex:i | ||
+ | |||
+ | Set Lock-Bits 0xEF:\\ | ||
+ | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U lock:w:0xEF:m | ||
+ | |||
+ | Run the [[http://www.atmel.com/tools/FLIP.aspx|Atmel Flip-Tools]] like it's described at [[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en//|Kimio Kosakas page]].\\ | ||
+ | Upload that file:[[http://make.kosakalab.com/archives/AVRISP-MKII_ATmega32u4.zip]].\\ | ||
+ | |||
+ | That's it! | ||
+ | |||
+ | Test it with an Atmega 328p:\\ | ||
+ | $ sudo avrdude -p m328p -c avrispmkII -P usb -U flash:w:optiboot_atmega328.hex:i | ||
---- | ---- | ||
Line 35: | Line 76: | ||
[[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_tpi.html|Atmel TPI Interfaces]]\\ | [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_tpi.html|Atmel TPI Interfaces]]\\ | ||
[[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_spi.html|Atmel SPI Interface]]\\ | [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_spi.html|Atmel SPI Interface]]\\ | ||
+ | |||
+ | === Avrdude manual === | ||
+ | [[http://www.nongnu.org/avrdude/user-manual/avrdude_4.html]]\\ | ||
+ | |||
+ | {{:avr_bootloader:paper-avrisp_mkii.jpg?300|}}\\ | ||
+ | ---- | ||
+ | ==== License ==== | ||
+ | |||
+ | The Paper-AVRISP mkII was designed by **Wolfgang Spahn** 2017.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | |||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
---- | ---- | ||