Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
analog_computer:confetti102_chua_diode [2020/05/09 22:09] admin [Paper PCB] |
analog_computer:confetti102_chua_diode [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Confetti102 Chua's Diode ===== | + | ===== Confetti 102 Chua's Diode ===== |
That's a [[https://en.wikipedia.org/wiki/Chua%27s_diode|Chua's Diode]] board for the analog computer [[analog_computer:analog_computer_main|Confetti]].\\ | That's a [[https://en.wikipedia.org/wiki/Chua%27s_diode|Chua's Diode]] board for the analog computer [[analog_computer:analog_computer_main|Confetti]].\\ | ||
With the jumper set one can connect the output to the common ground, if no jumper is used one can use the output connector instead.\\ | With the jumper set one can connect the output to the common ground, if no jumper is used one can use the output connector instead.\\ | ||
In combination with the [[analog_computer:confetti101_gyrator|Confetti101 Gyrator]] one can build a [[https://en.wikipedia.org/wiki/Chua%27s_circuit|Chua's Oscillator]].\\ | In combination with the [[analog_computer:confetti101_gyrator|Confetti101 Gyrator]] one can build a [[https://en.wikipedia.org/wiki/Chua%27s_circuit|Chua's Oscillator]].\\ | ||
+ | |||
+ | {{:analog_computer:chua_s_circuit_oscilloscope_134541.jpg?600|}}\\ | ||
+ | [[https://dernulleffekt.de/doku.php?id=analogcomputation:01_chuascircuit#analog_computation_01_-_chua_s_circuit|Analog Computing 01 - Chua's Circuit]]\\ | ||
---- | ---- | ||
Line 12: | Line 15: | ||
---- | ---- | ||
==== Parts ==== | ==== Parts ==== | ||
+ | * **Resistors:** | ||
+ | * 2x 330 Ohm | ||
+ | * 2x 3.3 kOhm | ||
+ | * 2x 47 kOhm | ||
+ | * **Diodes:** | ||
+ | * 2x 1N4148 | ||
+ | * **Semiconductors** | ||
+ | * 1x TL072 OpAmp | ||
+ | * **Mechanical:** | ||
+ | * 1x IC socket, 8pins | ||
+ | * 1x 2 pin strip | ||
+ | * 3x 2 pin header, female | ||
+ | * 2x pin header, female 90° 1x3, 1x2 | ||
+ | * 2x pin header, male 90° 1x3, 1x2 | ||
+ | * 1x jumpers | ||
+ | * **Trimpotentiometer:** | ||
+ | * 1x 5 kOhm | ||
---- | ---- | ||
==== License ==== | ==== License ==== | ||
- | The Confetti102 Chua Diode was designed by **Wolfgang Spahn** 2015-19.\\ | + | The Confetti102 Chua Diode was designed by **Wolfgang Spahn** 2015-20.\\ |
It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||